Specification:
Item Type: 380 Sensored Brushless Motor TS80 Sensored Brushless ESC Set
Material: Aluminum Alloy, Copper, Plastic
Color: Black
Weight: Approx. 260g / 9.2oz
Motor Model: 380
KV(RPM/Volt): 4000KV
Output Power: 250W
General Lithium Battery: 2S
Maximum Current: 60A
Number of Motor Poles: 2
No Load Current: 7.4V, 3.0A
Internal Resistance(): 23.0
Motor T Number: 10.5T
Motor Diameter: Approx. 27.8mm / 1.1in
Motor Length: Approx. 47.5mm / 1.9in (Without Shaft)
Shaft Diameter: Approx. 3.175mm / 0.2in
Shaft Length: Approx. 13.5mm / 0.5in
TS80A ESC:
Voltage Input: 6V-11V
Peak Current: 160A
Continuous Current: 80A
Forward, Brake, Reverse: Yes (Factory Preset to Forward, Brake)
Motor Limit: 540 motor Minimum Number of Turns 13.5T, 380 or 390 Motor Minimum Number of Turns 10.5T
Motor Type: Induction 380, 390, 540 Brushless Motor
B.E.C: 3A, 6V
ESC Size: Approx. 29.52x29.5x24mm / 1.2x1.2x1.0in (Including Fan)
Plug Type: XT60 (with Protective Cover)
Application: Suitable for 380, 390, 540 Brushless Motors, Fits 1/12 and 1/14 Scale RC Cars
Motor Installation:
-
Three connecting wires need to be welded to connect the motor. There is no fixed color distinction or no color distinction between the three connecting wires. Please pay attention to the following two points when installing and connecting:
A. When using the sensory ESC, firstly connect or solder the connecting wires of the ESC and the motor correctly, that is, the A, B,C of the ESC and the A, B, C of the motor are connected correspondingly to each other. Then use a good induction line and connect it to the induction interface of the motor and ESC according to the orientation of the correct solution.
B. When using the non inductive ESC, there is no fixed line sequence requirement for the connection between the motor and the ESC. If the direction is reversed, the two motor lines can be arbitrarily exchanged.
ESC Installation:
-
Connect the built in BEC cable (100mm) between the receiver connector and the ESC.
- Connect the 3 ESC wires to the motor; you can solder the wires directly to the motor or use your favorite connector. When soldering, match the (A, B, C) wires of the ESC output with the (A, B, C) solder lugs on the motor. Avoid soldering each joint for more than 5 seconds, which can cause the flow of tin to form a short circuit. (Warning! Improper wiring may damage the ESC shaft and void the warranty)
Features:
1Aluminum Alloy Shell: High strength 7057 imported aluminum alloy shell, unique smooth edge hollow design, ultra light weight, efficient heat dissipation. 2Size and Application: Standard 380 size, M3 16/19MM mounting hole spacing, 3.175mm output shaft, suitable for 1/12 and 1/14 scale remote control cars. 3Copper Wire Winding and Rotor: Original 1El/AIW(H) copper wire winding has extremely low resistance, super magnetic high temperature resistance, and EH grade rotor has more efficient energy of motion output. 4Bearing and ABC Copper Solder Tabs: High accuracy bearing makes the motor run more smoothly. The unique gold plated thickened ABC copper solder tabs operate freely at a high temperature of150C. 5Removable and Replaceable Design: The motor is designed with detachable and reorganized structure, which is convenient for cleaning and maintenance, and effectively prolongs the service life of the motor. 6ESC Performance: The ESC has built in super BEC, independent programming connector, combined 8bit processor, lowresistance FET continuous current. 7Good Performance: Aluminum shell and mesh radiator, high efficiency cooling system, high performance removable cooling fan (23000rpm/7.2V).
Package List:
1 x 380 Induction Motor
1 x TS80A Inductive ESC
1 x Induction Wire
2 x Storage Box
2 x Manual
