Description:
This high quality DC micro diaphragm pump with a pressure switch will be automatically cut off when the pressure of water outlet is big enough. And runs again when the pressure is going down. It is not a good idea let this pump runs dry for too long. This type of product can be applied to occasions, which have demand for energy conservation and frequent switching, such as machine washing, feeding water to a solar energy system, and remote automatic controlling system of conveying water and suspending water supply, etc.
Features:
-
With a pressureswitch it will be automatically cut off when the pressure of water outletis big enough. And runs again when the pressure is going down.
-
The mounting feet are rubber instead of rigid plastic, which provides fairly good vibration isolation.
-
Built-in pressure switch, it automatically turns on and off as you turn your tap or nozzle on and off.
- Water inlet and outlet interface connect with silicone PE or PU pipe.
Specifications:
Volts: DC12V
Power: 60W
Flow Rate: 5L/min
Max Working Pressure: 116psi (0.8MPA)
Pumping head: 1.5m
Outlet head: 30m
Size: 9.9 x 16.7cm / 3.9" x 6.6"
Line Length: 29cm / 11.4"
Interface Outer Diameter: Approx. 10.8mm / 0.4"
Interface Inner Diameter: Approx. 6mm / 0.2"
Package Weight: 688g
Application: Can be widely used for garden sprinklers,shower, water taps in the boat, caravan or motor home. Agricultural purposes: spray for farm chemical, pesticide.
Instructions:
- The arrow mark of the pump represents the water outlet and the other side is the water inlet.
- connect the pump to the inlet and outlet pipes, you must ensure a compact connection between the inlet /outlet pipes and the pump. Failure to do so may result in low pressure or leakage.
- For the Inlet filter,it is required to have greater than 80 mesh filter density (EG 1 square centimeter 80 holes).
- Turn on the power, andthe pump start running.5-10 seconds of water effluent, the air in the pump and piping will be emptied. After the water effluent is stable, temporarily turn off the power and connect the water gun (or similar tools).
Warm Tips:
- According to the water pump parameters,please select the corresponding voltage, current,flow diameter blowholes and similar tools.
- The water pumpis strictly prohibited to place intothe water; Please Installed it in a dry, ventilated location;
- The pressure adjustment screw can be adjusted freely.If the pump pressure is high, it is easy to suppress the burst pipe before delivery pressure is adjusted.Tighten the screw down, it will be high pressure;loosen the screw will lower the pressure.High pressure and high current will affect the lifespan of the water pump.
- Do not use hot water more than 60high temperature or dirty water (Mud and sands in dirty water will make the pump clogged and ruin the pump)
- Prohibited to use this pump without using a filter. The mesh density is better to be more than 80 mesh.
- The diameter of the blowhole must conform to the specified value, otherwise the motor pump might be damaged .
- For home use only, not for commercial use, no warranty for commercial use (to avoid overheating and shortened service life, intermittent work is recommended wherever possible).
- It is recommended that the complete power cord should not be 0.75 square (copper wire) and 2.5 meters long. It should not be too long or too thin.
- If the pump does not absorb water, please select the corresponding current (3A-12A) for the power supply. Makethe inlet to draw the water or the outlet to suck the water.Check whether the inlet water is in the opposite direction, or there is any impurities in the pump. Make surethe suction Vertical distance is in Within 1-2 meters, the upper and lower diaphragms are mounted, etc.
- The pump can not put in water, the motor can not touch water. 12 volt pump can't use directly with 220 volt household electricity without transformer. It can not use with 24 volts, 38 volts. Due to the above reasons, the failure is not guaranteed ! ! This pump is a Intermittent type pump, it can not be used continuously for a long time. The specific time depends on the use of the application. Please select the matching current 3A-12A, as excessive current may burn out the motor.
Package Included:
1 x Self Priming Pump
Note:
-
The motor still won't stop running even the water outlet is blocked but the reflux valve will be opened and water circulates in the pump in that situation.
-
This type of product can be applied to occasions that have low level of demand for energy conservation.
-
Please allow 1-3cm error due to manual measurement. Thanks for your understanding.
